15570 Stony Creek Way
 Noblesville, IN 46060
 USA
 

H o m e
P r o d u c t s

  Kit Boxes
C a t a l o g
C o n t a c t s
A b o u t
I n q u i r i e s
E m a i l

Kit Boxes - page 1

 

 

Kit Boxes (page 2)
O-Ring Kit, metric & imperial
Splicing Kit
Copper Sealing Washer Kit
Fibre Washer Kit
Bonded Seals Kit
Spring Roll Pins Kit
Split Cotter Pins Kit
Circlip & E-Clip Kits
Grease Nipple Kit
O-Ring Vulcanising Kit
 

O-Rings


Cross section diameter gauges moulded into the o-ring kit box itself, are accurately calibrated cross section slots. These slots assure precision measurement of o-rings to be replaced.

Contents List:

BOXH Metric o-rings
NBR 70° Shore A
30 sizes = 404 pcs.

18 pcs  3 x 2
18 pcs  4 x 2
18 pcs  5 x 2
18 pcs  6 x 2
17 pcs  7 x 2
17 pcs  8 x 2
17 pcs 10 x 2
14 pcs 10 x 2.5
14 pcs 11 x 2.5
14 pcs 12 x 2.5
14 pcs 14 x 2.5
14 pcs 16 x 2.5
14 pcs 17 x 2.5
14 pcs 19 x 2.5
12 pcs 19 x 3
12 pcs 20 x 3
12 pcs 22 x 3
12 pcs 24 x 3
12 pcs 25 x 3
12 pcs 27 x 3
12 pcs 28 x 3
12 pcs 30 x 3
12 pcs 32 x 3
12 pcs 33 x 3
12 pcs 35 x 3
12 pcs 36 x 3
12 pcs 38 x 3
 9 pcs 38 x 4
 9 pcs 42 x 4
 9 pcs 45 x 4
BOXG Imperial o-rings
NBR 70° Shore A
30 sizes = 382 pcs

AS 006 20 pcs  2.9  x 1.78
AS 007 20 pcs  3.68 x 1.78
AS 008 20 pcs  4.48 x 1.78
AS 009 20 pcs  5.28 x 1.78
AS 010 20 pcs  6.07 x 1.78
AS 011 20 pcs  7.66 x 1.78
AS 012 20 pcs  9.25 x 1.78
AS 110 13 pcs  9.19 x 2.62
AS 111 13 pcs 10.78 x 2.62
AS 112 13 pcs 12.31 x 2.62
AS 113 13 pcs 13.95 x 2.62
AS 114 13 pcs 15.54 x 2.62
AS 115 13 pcs 17.13 x 2.62
AS 116 13 pcs 18.72 x 2.62
AS 210 10 pcs 18.64 x 3.53
AS 211 10 pcs 20.22 x 3.53
AS 212 10 pcs 21.82 x 3.53
AS 213 10 pcs 23.40 x 3.53
AS 214 10 pcs 24.99 x 3.53
AS 215 10 pcs 26.58 x 3.53
AS 216 10 pcs 28.17 x 3.53
AS 217 10 pcs 29.75 x 3.53
AS 218 10 pcs 31.34 x 3.53
AS 219 10 pcs 32.92 x 3.53
AS 220 10 pcs 34.52 x 3.53
AS 221 10 pcs 36.10 x 3.53
AS 222 10 pcs 37.69 x 3.53 AS 325 7 pcs 37.47 x 5.33 AS 326 7 pcs 40.65 x 5.33 AS 327 7 pcs 43.82 x 5.33

Also available in Viton and Nitrile 90°

Splicing Kit

HOW TO MAKE AN O-RING
To calculate the correct length of cord required, multiply the inside diameter of the o-ring by pi, then add 1x cord diameter. This will then give the correct length of cord required.
Using the splicing aid and a very sharp knife. make a cut in the material at a right angle. All surfaces to be glued must be free of oil or grease. Avoid touching the surfaces. A thin layer of glue should be spread over one side of the cut. A thin layer provides the best results. In order to join the two sides cleanly, use the V section on the splicing aid. Match both surfaces together and press firmly for 15 seconds. The glue must dry for 60 seconds before mounting the O-ring

Splicing kit

Kits available:
(see contents list)

  • Kit  S - 11 size Splicing Kit
  • Kit SL - 16 Size Splicing Kit

Contents List SPLICING KIT ll size

2M C0178  1/16 nom
   C0262  3/32 nom
   C0350  1/8  nom
   C0533  3/16 nom
   C0699  1/4  nom
2M CO160  1.6mm
   C0200  2.0mm
   C0300  3.0mm
   C0400  4.0mm
   C0500  5.0mm
   C0570  5.7mm
TOOL BOX
KNIFE
LF600 (5g glue)
BLOCK

+ these for the 16 size kit

2m CO150 1.5mm
   C0240 2.4mm
   C0250 2.5mm
   C0350 3.5mm
   C0840 8.4mm 

Copper Sealing Washer Kit

Kits available:
  • AB32 - Copper Washer Kit (up to 1" ASP)
  • AB92 - Metric Copper Washer Kit
Copper sealing washers


Top
Phone: 317-776-3095 Fax: 317-219-0512
 

 

Illustrations and artwork on this site © Supaseal (uk) Ltd, unless otherwise stated.